在FreeBSD Linux上如何检查硬盘的健康状况
时间：2019-11-20 08:53:42 来源:igfitidea点击:
在Linux中，如何检查硬盘的状态？
在FreeBSD Linux上，如何对硬盘进行健康检查？
如何使用smartctl命令读取硬盘的运行状况？
如何在FreeBSD上安装smartmontools？
解决方案
现代的硬盘一般都内置了SMART系统（Self-Monitoring, Analysis, and Reporting Technology System），即自我监控，分析和报告技术系统。
在FreeBSD上安装smartmontools
使用FreeBSD ports进行安装：
# cd /usr/ports/sysutils/smartmontools # make install clean
或者使用pkg命令安装二进制包：
# pkg install smartmontools
smartmontools软件包中包含了两个实用程序：
- smartctl命令 用于控制和监视硬盘的运行状况。
- smartd 这是一个守护程序，它监视硬盘的运行状况并向用户发出有关问题的警报。
在FreeBSD上如何检查硬盘的健康状况
检查驱动器的状态语法如下：
smartctl -a /dev/disk
首先在FreeBSD中查看所有连接到系统的硬盘：
# camcontrol devlist
或者从启动日志中查找：
# egrep 'ad[0-9]|cd[0-9]' /var/run/dmesg.boot egrep 'da[0-9]|cd[0-9]' /var/run/dmesg.boot
FreeeBSD检查硬盘的健康状况
查看硬盘的信息
# smartctl -i /dev/ada0
输出示例：
smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.2-RELEASE-p10 amd64] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD60EFRX-68MYMN1 Serial Number: WD-XXXXXXXXXXXXXXX LU WWN Device Id: 5 0014ee 26195240d Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 20 22:53:06 2019 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled
检查磁盘运行状况，运行：
# smartctl -a /dev/ada0
输出示例：
smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.2-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST Deskstar NAS
Device Model: HGST YYYYYYYYYZZZ
Serial Number: K1JVDUGD
LU WWN Device Id: 5 000cca 255e830c9
Firmware Version: APGNW7JH
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon May 20 23:00:59 2019 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 138 138 054 Pre-fail Offline - 100
3 Spin_Up_Time 0x0007 149 149 024 Pre-fail Always - 436 (Average 449)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 43
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 8501
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 42
192 Power-Off_Retract_Count 0x0032 095 095 000 Old_age Always - 6673
193 Load_Cycle_Count 0x0012 095 095 000 Old_age Always - 6673
194 Temperature_Celsius 0x0002 117 117 000 Old_age Always - 51 (Min/Max 25/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
如何配置Smartd发送电子邮件警报
编辑文件：
# cd /usr/local/etc # cp smartd.conf.sample smartd.conf # vim smartd.conf
注释掉或删除所有DEVICESCAN行：
# DEVICESCAN
设置要监视的设备。例如：
/dev/ada0 -a -m disk.admin@your-tld
也添加所有磁盘：
/dev/ada1 -a -m disk.admin@your-tld,root@localhost
确保smartd在引导时启动：
echo 'smartd_enable="YES"' >> /etc/rc.conf
如何启动/停止/重启smartd服务
# service smartd start # service smartd restart # service smartd status # service smartd stop
